Schumacher's test hampered by rain Racer

12.01.10

Michael Schumacher's return to liveliness in the GP2 development test at Jerez in Spain was cut short by bad weather on Tuesday.

The seven-time advocate, who is making a Formula 1 comeback this year with Mercedes GP, managed to complete 52 laps on the first day of the scheduled three-day run before hard up weather forced him to bring running to a premature halt.

Despite the weather, Schumacher was contented to have got at least a little experience under his belt in the test aimed at acclimatizing him back to F1 speeds – and also providing GP2 with some feedback on its car.

"The day today was dependable especially because after a long time I could drive again in a car that came almost close to a current Formula 1. In the face the weather not being what we all would have liked, all my senses were nevertheless on full alert – this alone was worth it," he said. "I felt comfortable out on the spoor from the very beginning, and naturally I'd like to thank our Team and the GP2 series very much for the opportunity to drive."

Source:

dryer belt????????

Apr 09, 2008 by Nate M | Posted in Maintenance & Repairs

where could i find a diagram or video on how 2 transform a dryer belt i cant find it someone told me to take out the tumbler i cant seem to figure out how to get to the belt i have an old electric whirlpool dryer

I come up with on most dryers of your type you must first lift the top. There are 2 spring catches you must release. They are accessed by placing a 'thin' putty stab the crack between the top and front surfaces about 3 inches from each edge,,and push. If the lint filter is in the machine top, first remove the 2 screws below the screen.
After you Lift the top you will see the drum. Remove the door switch electrical wire.
The front panel of the dryer acts as the front conduct for the drum so as you remove the 2 screws holding the front panel in place,top L&R be ready to support the drum. Take the front panel from the 2 alignment pins at the bottom. You now have access to install the belt kit.

flea | Apr 09, 2008

Have you looked within a dryer. It is pretty simple. There is usually a bearing in the back, take out the 2 to 4 screws and slip the belt on, put it around the motor and put the screws back in.
protoham | Apr 09, 2008

Have you tried fascinating off the back of the dryer? That is usually where they are on the older ones. In the back and low I think. If you still cant find it then try and find the motor, just follow the electrical wires for that. They belt is on a site on the motor. Good luck
oilers7134 | Apr 09, 2008

go to were stores were Whirl dryers are sold and ask for a copy of there instructions on dryers
Baby | Apr 09, 2008

I reckon on most dryers of your type you must first lift the top. There are 2 spring catches you must release. They are accessed by placing a 'thin' putty cut the crack between the top and front surfaces about 3 inches from each edge,,and push. If the lint filter is in the machine top, first remove the 2 screws below the membrane strain.
After you Lift the top you will see the drum. Remove the door switch electrical wire.
The front panel of the dryer acts as the front mien for the drum so as you remove the 2 screws holding the front panel in place,top L&R be ready to support the drum. Immortalize the front panel from the 2 alignment pins at the bottom. You now have access to install the belt kit.
flea | Apr 09, 2008

Try this place,explains it all.
rick c | Apr 09, 2008

How do you replace a tumble dryer belt?

May 27, 2008 by Katie F | Posted in Maintenance & Repairs

I bought a new belt, and am taxing to repair my tumble dryer (a Creda 37751).

As fas as I can tell, the belt has to go around the drum, the motor and then the two pulleys. It seems too tight, though, and the drum won't finger.

Any suggestions?

did u get the put right size belt for your dryer? u have to get the belt around the drum so lift the top lid of the dryer....stick something stiff and flat in the front of the dryer lid...there are 2 clips about 4 inches from each end....fitting push on the clips and lift the lid.....next u have to get the drum loose from the front door....look for the screws to do this....take off the drum from the door gasket just far enough to get the belt around it...then around the pulleys and motor

uclueletbc | May 27, 2008

What kind of belt dressing does a squeaky dryer belt need?

Jan 06, 2009 by gladiado | Posted in Cleaning & Laundry

I have a Kenmore dryer several years old but still does the job very well only has started squeaking and squeal-ling a lot lately. I be versed there are "belt dressing" but where does the stuff go and seems like decades ago petroleum jelly was worn. Can anyone help me on this?

Unceasingly a once to replace the belt. It's stretching and squealing.

OneLastRevolutionary | Jan 06, 2009
Cantilever Umbrella

Dryer Belt - News


Results tagged “free choice” SEIU Blog
- Mar 17, 2009
Results tagged “rid choice”SEIU Blog, DC 2007, Eleazar Torres-Gomez was killed when he tried to unjam an industrial conveyor belt at an Oklahoma shrub of Cintas, an industrial laundry company. He was dragged into an operating industrial dryer, and trapped inside it for twenty minutes.

Restaurant review: The Church Green guardian.co.uk
- Mar 14, 2009
Restaurant review: The Church Green guardian.co.uk defender.co.ukRestaurant review: The Church Greenguardian.co.uk, UKAt these prices, one expects such fripperies as a working dole out dryer in the loo and linen napery; or at least, when the dryer breaks down, that someone would transfer the paper napkins to the gents for that elite corps of masculine punters without a fetish



Leave a Reply